Our LGX Low Gloss X-treme™ provides maximum protection with minimal shine. Our premium sealers color enhancing formula protects high-traffic pavers from weathering, chemicals, rust, and salt damage. The breathable formula provides added UV protection while leaving your surfaces looking restored.

Features: 

• Low-Gloss Finish
• High Color Enhancement 
• Solvent-Based Formula
• Minimizes Salt and Freeze/Thaw Damage
• Provides UV protection
• Highly durable/long lasting protection and enhancement 
• Ideal for High-Traffic Areas
• Breathable 
• VOC Compliant

Applications: 

• Concrete Pavers
• Concrete Permeable Pavers
• Wetcast
• Granite/Quartz
• Marble/Travertine
• Limestone
• Manufactured Stone
• Stamped Concrete

Product Details: 

LGX Low Gloss X-treme | Premium Seal

LGX VOC Low Gloss X-treme | Premium Seal

Instructions: 

1. CLEAN

   1. Wait 28 days after installing polymeric sand before sealing.
   2. Thoroughly sweep or blow the surface of joint sand or loose material.
   3. Spot clean if needed with one of these SRW Products specialty cleaners:
      
      1. CDX = Cleaner & Degreaser X-treme for oil and grease spots.
      2. RE = Rust Eliminator for rust and mineral removal.
   4. Prepare all pavers with one of these SRW Products cleaners:
      
      1. EF = for Efflorescence removal.
      2. PW = Paver Wash for general cleaning & polyhaze removal.

2. CLIMATE

   1. After cleaning, wait at least 24 hours before sealing. Surface and joints must be completely dry.
   2. Recommended application temperatures are 50° – 80°F (10° – 27°C) from installation through the cure process.
   3. Do not apply if inclement weather is forecasted within 24 hours.

3. APPLY

   1. It’s important to STIR THOROUGHLY before application.
   2. Apply with an SRW Products-approved Slit Foam Roller and sprayer.
   3. Spray, then back roll. This prevents an uneven finish.
   4. A 2-person application is recommended.
   5. Always spray against a wet edge and do not overlap a previously sealed and dried area.
   6. Start at the highest project elevation.
   7. Do not allow sealer to pool on pavers or in joints.
   8. Repeat if desired.

4. CURE

   1. Allow the sealed area to dry and cure for 24 hours.
   2. Protect the area from water and rain until dry.
   3. Curing time ranges:
      
      1. Dry-tack free: 25 minutes.
      2. Foot traffic: 24 hours.
      3. Vehicle traffic: 72 hours.
      4. Note: All calculations based on 68°F-77°F (20°C-25°C).

5. COVERAGE

   1. Up to 250 sq. ft. per gallon (23.23 sq. m. per 3.78 liters).
   2. Coverage may vary depending on surface & application.

6. CLEAN UP & STORAGE

   1. Clean sprayer & tools with SRW Products XY Xylene Solvent™ specialty cleaner.
   2. Store container in a cool area with cap or lid firmly in place.

7. RECOMMENDED TOOLS

   1. For best results, use an SRW Construction Sprayer & a Slit Foam Roller X-treme to apply.

8. USER TIPS

   1. Test in an inconspicuous area before starting the general application to ensure desired results & expected finish.
   2. Always follow hardscape manufacturer’s sealing recommendations.
   3. If using on manufactured stone, ask dealer about cleaning & sealing procedures prior to application.
   4. For a deeper sheen, wait at least 4 hours before applying a second coat. This ensures the highest gloss appearance. Do not over apply.
   5. For added slip resistance, use SRW SR Slip-Resist™.
   6. Do not use more than one sealer on the same project.
   7. Not for use on clay pavers/brick, slate, sandstone/bluestone or polished stone.
   8. Not for use on structures under hydrostatic pressure. 
   9. Not for use on permeable pavers.
   10. Not for use on concrete overlays.